|
11/18/2009 11:36:42 AM
|
topic:
Minor slope fix
The Tile Shop
Posts 15
|
epk,
You could do either: mud a bit more to make the slope meet the wall - or - backbutter your tiles that go over the level portions to create a slight pitch. I suggest you mud the last part and be confident you have sloped the whole base correctly.
|
|
11/16/2009 8:28:29 PM
|
topic:
Minor slope fix
epk
Posts 4
|
OK, everything has gone perfectly (I really like that Pro Curb) up to the top layer of MIchigan Mud.
The final base-tile layer of the shower pan has dried about 24 hours. I found an area of level slope along the outside (it was a little tricky because of rectangle shape). Its about a six inch by twelve inch area that I overlooked as I started doing more harm than good to the surface.
Time is not a problem, what is the best way to correct? Can I use a thin layer of MIchigan Mud? Otherwise the thin-set?
Thanks!
|
|
11/14/2009 8:55:55 AM
|
topic:
Pro Curb question
The Tile Shop
Posts 15
|
Thanks for the question !
I tnink there is a slight slope from on side of the pro curb to the other. But , Yes, if you want to make sure that the top of the shower curb slopes towards the shower, then I would put a shim on the outside of the curb.
If you want, you can secure the curb to the wall you can do so as well. I would if it was my project, it is better to be sake than sorry. But in most cases the weight of the floor mix, and the is all it calls for.
I hope this helps, let us know if you have any other questions.
|
|
11/13/2009 9:32:12 PM
|
topic:
Pro Curb question
epk
Posts 4
|
A few questions on the pro curb:
1. The DIY video and brochure indicate that the pro curb is tapered. I've studied both sides and can't see a difference. Is there a taper, and if so what should I look for?
2. If there is no taper should I shim under one side or just install it square and taper the top tile.
3. Does the pro curb attach to anything, or is the weight and grip of the michigan mud to the tar-paper enough?
Thanks!
|
|
11/13/2009 8:52:29 AM
|
topic:
Installing a corner bench
The Tile Shop
Posts 15
|
Erik,
I like the idea of the horizontal 2x4 and contruction adhesive to adhere the seat to the board..
2. I would use silicone around the edge of the notch, rather than contruction adhesive.
Thanks again for the question,
Carl
|
|
11/13/2009 7:08:52 AM
|
topic:
Installing a corner bench
epk
Posts 4
|
Thanks - couple more questions - looking for your advice on "over-engineering" to make the seat as strong as possible:
1. Would you recommend that I use construction adhesive between the back edge of the seat and the vertical 2x4's? Or maybe add a horizontal 2x4 for more adhesion?
2. Would it help to add construction adhesive around the seat to the cement board notch?
Thanks,
Eric
|
|
11/12/2009 1:40:51 PM
|
topic:
Installing a corner bench
The Tile Shop
Posts 15
|
EPK,
These are great questions.
1. Rush River Stone shower seats can hold up to 300 lbs.
2. To install the seat, make a notch in the cement board. try to make the slot tight to the seat.Install the seat into the notch and tile around the seat. Make sure you allow for a slight slope so water can drain off the seat. After the tile is grouted, use 100 % silicone to caulk around the seat.
|
|
11/12/2009 1:09:04 PM
|
topic:
Installing a corner bench
epk
Posts 4
|
I have a stone corner bench that I plan to install in a custom shower installation. I'm still building the shower pan now.
I have not seen clear instructions or DIY video on the strongest installation of the bench. Such as
1. What carries the weight?
2. Do I use adhesive direct to the framing? Vertical framing or would it be better to put in some horizontal boards at the right height?
3. How tight should I make the rockboard cut-out? Does that support some of the weight? Should I cut the slot at an angle?
Thanks
epk
|
|
11/12/2009 12:11:43 PM
|
topic:
Exterior Tile Installation
dan
Posts 3
|
What problems could I expect if water/snow isn't immediately cleared? Although I really want a tile floor, I don't want to invest in this project if I can't have a relatively maintenance free floor for many years (I know I have to seal grout joints once a year). I don't want to have to redo the floor in 5 years due to tiles popping and grout joints constantly cracking. What do you think is the liklihood of this happening?
Thanks,
Dan
|
|
11/12/2009 11:27:38 AM
|
topic:
Exterior Tile Installation
The Tile Shop
Posts 15
|
Dan,
In that case, slope the pitch as much as you can. You will need to periodically clear the water and/or snow during the heavy weather months.
|
|
11/12/2009 7:15:15 AM
|
topic:
Exterior Tile Installation
dan
Posts 3
|
Hi,
I won't be able to build up a mud floor greater than 3/4" for slope as the tile would be above the door sills.
It is a porch with a roof overhead; it isn't a 3-season screened in porch.
Thanks,
Dan
|
|
11/11/2009 11:41:42 AM
|
topic:
Exterior Tile Installation
The Tile Shop
Posts 15
|
Dan,
This would be the best method if you want the water to drain off your porch. But are you able to do this with only 1" to play with. The mud floor has to be a min thickness of 3/4". The tile and adhesive will be another 3/8". That doesn't leave much room for drainage.
Is this a 3 season screened in porch ?
|
|
11/11/2009 9:46:03 AM
|
topic:
Exterior Tile Installation
The Tile Shop
Posts 15
|
Dan,
Both The Tile Shop and the installer are correct. The safest altenative is to "slope the floor". However, this would be difficult using 1/4 " durock. I would recommed installing a mud ( cement and sand mix) subfloor, starting at the door jam, and gently sloping towards where you would like the water to drain. I would then use our Pro Shield over the top of the subfloor to waterproof and act as a anti fracture membrane to minimize any chance of cracking because of movement of the structure.
We have a picture of a screened in porch on our web site on page 7 of our Distinctive Places galley that is very similaer to the projoct you are working on. The floor was framed with 2x12's, and 3/4 " green treates plywood, with durock used as the subfloor for the natural stone slate tile on the floor. The similarity is this project is in Minnesota, and is exposed to harsh conditions. To this date the prorch project still looks great with no problems. It is your choice with method to use, but we have found the mud floor option to be the best.
edited by The Tile Shop on 11/11/2009
|
|
11/11/2009 8:39:34 AM
|
topic:
Exterior Tile Installation
dan
Posts 3
|
I would like to install porcelain tile on a covered porch I built in Ohio. The porch is elevated with a walk-out basement below and is framed with 2x12, 12" o.c. with treated plywood, and is 20' out from the house.
The problem is there is no slope to the floor, and exterior door sills are only an inch or so above the treated plywood.
The sales person at the local Tile Shop insists I can install 1/4" cement board above the plywood, paint a rubber waterproofing membrane over, then install the porcelain tile with their Superior Pro-lastic polymer mortar approved for exterior use. I would like to do this, however, local installers and further internet research say that tile should not be installed outdoors without slope of 1/4" per foot. Even though the porch is covered, there will be driving rain and snow that may end up on the tile floor.
Your advise is sincerely appreciated.
__________________
dan
|
|
10/6/2009 8:36:29 AM
|
topic:
Pro Shield HPG
The Tile Shop
Posts 15
|
1/4 Hardieboard after taping would be the preferred application. For specific information on your project contact either the nearest store here: http://www.tileshop.com/storelocator/index.aspx , or call our customer service line at: 1.888.389.6595
The Tile Shop Customer Service Team
|
|
10/4/2009 11:19:24 AM
|
topic:
Pro Shield HPG
ehoffman74
Posts 1
|
Our remodel is going relatively smoothly, but can't remember Tile Shops recommendation for the best location for use of the ProShield HPG waterproof membrane. Is it best installed on our exterior grade osb (oriented strand board) subfloor or on top of the 1/4" hardi board. If hardi board is OK do we install the reinforcing joint tape before or after proshield application. Final finish material is a 3/8" marble mosaic tile. Appreciate any thoughts.
|
|
9/18/2009 8:43:08 PM
|
topic:
Cleaning Slae
kimzab9
Posts 1
|
We have a slate shower The soap and shampoo seem to leave a white hue on the slate. What would be recommended for cleaning this?
|
|
8/27/2009 8:20:25 AM
|
topic:
Problem around light switches
Inspired
Posts 1
|
I'm getting ready to do a kitchen backsplash using glass bridgeport brick and some accent tiles. It's my first tiling project and I think I have everything I need and am dying to get started but I have a tricky issue with two double lightswitches. I plan to only tile to the edge of the countertops and these lightswitches are in the area I will be tiling but only partially. I understand I can get extenders for the other outlets that are completely in the tiling area, but what do I do about light switches that are half on the to-be-tiled area and half on the regular wall? I would extend it out past the countertop to go around the wall switch, but the kitchen opens to the livingroom and the wall color is different starting at the end of the countertop and it will look very odd for the tile to extend into the livingroom space.
|
|
8/6/2009 8:35:50 AM
|
topic:
Estimating tile needed for a project
cody1111
Posts 1
|
I'm trying to figure out how much tile I will need for above my kitchen sink, stove and countertop. I measured each section's height and width in inches. I multiplied each section out to get numbers for each individual section. I now have a total of 2,411 square inches. I divided that buy 12 to get the number of square feet that I need. I came up with 200 square feet of tile needed. Did I do that right?
I'm very new at this!
|
|
6/4/2009 11:33:29 AM
|
topic:
floor leveler
The Tile Shop
Posts 15
|
Chris, self leveler would be the answer. It is important to prime the surface first. (usually 2 coats) let dry, apply lathe(metal or plastic) and then pour self leveler according to instructions. We find this product easy to use and saves time and labor, plus gives you a flat floor. Contact our store nearest to you for any additional questions or products.
Thank you for an excellent question.
Tile Shop customer service
|
|
pages:
1 2
|